WELCOME TO THE NEW 475
WEEKDAYS 9AM-6PM EST CALL 800-995-6329
Project Spotlights

Alford, MA: GUTEX Roof Makes Sustainable High Performance

December 5, 2014
Ultratherm

GUTEX UltraTherm – a vapor open alternative to foam

We’ve blogged about the many benefits of GUTEX wood fiberboard insulation for truly green construction – see this video introduction and our GUTEX primer. To begin with, it’s one of the most sustainable insulation products, created from wood scraps and manufactured with a super efficient dry process for minimal environmental impact. It is also very practical, delivering continuous insulation and weather protection in one step. The tongue and groove edges make installation a snap and result in a windtight and waterproof exterior layer that can be exposed for up to three months. And unlike rigid foam, this insulation is vapor open – with 44 perm/in – to ensure that moisture in your walls can dry out if unforeseen humidity or moisture enters the enclosure.

These features are on display on a recent project in Western Massachusetts. The new construction home followed EcoNest principles for a “holistically designed and hand-crafted natural home” – using timber-frame, straw-clay walls, earth plasters and natural and non-toxic finishes. The walls were constructed with foam-free Durisol ICF blocks. For the roof, the project planned to use closed cell foam to insulate the cathedral ceilings. While healthy and green are two words not typically associated with foam (see here for more on this topic), this project seemed resigned to using closed cell foam to reach the R-49 residential code requirement that had gone into effect in July 2014 for climate zone 5.

IMG_5349

Foam-free solution for R-49 roof: R-41 cellulose plus R-8 GUTEX UltraTherm 60 (2-3/8″) wood fiberboard

 

Things took a different turn after 475 proposed GUTEX UltraTherm over densepack cellulose for an R-49 foam-free roof insulation system. Evan Hardcastle from 377 Builders crunched the numbers, and it didn’t take long for the team to jump on board. The switch to foam-free didn’t require modifying the 2×12 structure – especially important for a project already well underway – and just needed a few inches of exterior insulation over cellulose to meet the new code.  For everyone in climate zones 5 and 6 who needs to hit R-49, here’s the math:

  • 2×12 rafters densepacked with cellulose (R-3.7/in) yields R-41.6. (11-7/8″ I-joists get you to R-43.9)
  • A layer of UltraTherm 60 (60 mm thick, or 2-3/8″), at R-3.4/in, adds R-8
  • Total nominal R-49.6
  • For those going for Passive House or just want to factor in thermal bridges (assuming rafters 16″ o.c.), the total effective R-value comes in around R-44
  • For comparison, the effective insulation of 11.25″ closed cell foam is R-50, or R-4.5/in – about 25% less than nominal

The cellulose-GUTEX combination offers a vapor open assembly with superior drying potential. For interior vapor control, code requires a Class I or II vapor retarder. The solution: INTELLO Plus fastened to the inside of the rafters to provide airtightness, intelligent vapor control (Class II vapor retarder in winter and vapor open in summer) and netting/support for the blown in cellulose. (See here for a project with INTELLO Plus at the cathedral ceiling.) With its superb airtightness, INTELLO is the perfect accompaniment to exterior windtight GUTEX.

Installation

Installation is easy (especially with a cherry picker). UltraTherm boards are 23.6″W x 70.1″L (1780 x 600 mm) – and at 39 lbs are easy for one person to handle. They come factory tongue & grooved to span multiple rafters, so no need to worry about lining up with rafters! Just cut the last piece in the row for a nice press fit.

    
A tap here and there – from above or below – gets the GUTEX windtight and secure. After the boards are installed, 2×4 strapping is added for structure and back-venting. A rainscreen on your vapor-open roof is essential for optimal drying potential.

    
In the project shown, a waterproof roof offers a belt-and-suspenders approach, but in rainy Europe GUTEX is commonly installed under nothing but clay roof tiles – and GUTEX provides all the necessary drainage.  The GUTEX is the WRB.  However, while a secondary WRB isn’t required over all of the inter-locking wood fiberboard, valleys need to be addressed with Pro Clima Primer RP and TESCON Vana tapes, and we recommend wrapping SOLITEX Mento 1000 (or similar waterproof membrane) around the first (lowest) GUTEX course to provide drainage to a gutter. And the roof cladding can wait – GUTEX has 3 month exposure.

    
With the roof exterior windtight and weathered in, the Alford project continues to make the house airtight at the interior. Interior airtightness is our best practice recommendation for a number of reasons – see this blogpost. The interior airtight plastered Durisol walls connect to windows, doors and INTELLO Plus air/vapor on adjoining wood-framed walls and roofs using CONTEGA FC – a special fleece tape ideal for these types of airtight connections.

Sustainable high-performance.

, , , , , , ,

Tweet about this on TwitterShare on FacebookShare on LinkedInPin on PinterestEmail to someone

3 Responses to Alford, MA: GUTEX Roof Makes Sustainable High Performance

  1. tom gray December 11, 2014 at 2:38 pm #

    so the 2 x4 strapping runs up the slope screwed to the Gutex or must it hit 2 x 12 s? Layer of OSB then shingles?

    • DrHouse December 14, 2014 at 6:42 pm #

      From what I can tell, it looks like the engineer designed the roof with a two ply 2×12 at 24″ O.C. to provide a bigger target for the lag screws. The 2×4 strapping would then be lagged through the non-structural Gutex and into the double 2×12 below to satisfy the design load requirements. I imagine you could then sheath and clad the roof as desired. Maybe 377 Builders can weigh in with some more details. Nice project!

      • John December 16, 2014 at 9:24 am #

        We consulted Evan from 377 who said:
        “Dr. House got it exactly right. The engineer designed the roof with two ply 2×12 rafters at 24″ O.C. to provide a bigger target for the lag screws. The 2×4 strapping would then be lagged through the non-structural Gutex and into the double 2×12 below to satisfy the design load requirements. I imagine you could then sheath and clad the roof as desired.’ We used Headlok lag screws at 12” oc with countersunk heads to connect the 2×4’s running in line with the double 2×12’s. This was, and is, a very cool project and 475 has played a pivotal role in making the air sealing and insulation systems work.”

Leave a Reply